You can get your amp out of protect mode by making sure all the cables are connected, amp is not overheating, amp gain is properly adjusted, the ground connection is not loose, etc.
If it’s still having the issue after applying all these methods, then you should disconnect all other components and connect them again one by one to see if they’re faulty instead.
If all other components are good and the issue still persists, then it means there’s an internal fault in the amp which may require a professional repair – or you can replace it with a new amplifier such as Rockford Fosgate R500X1D.
A car amplifier is one of the major components of a car audio setup. It receives the audio signal and amplifies it before sending it to the speaker.
Without an amp, the audio signal would be too weak to move the speaker physically, and you won’t hear any sound.
Some people assume that an amp is only required for premium audio setups, but this can’t be any further from the truth. While it’s true that basic car audio systems consist of only a head unit and speaker(s), a small-capacity amp comes pre-installed in that head unit.
But if you want to hear loud music without distortion or add a subwoofer to your system, you will need a separate 3rd-party amplifier.
Since it works with other components of your system, any malfunction in your amplifier can also cause damage to other components, such as your speaker.
In case of such malfunctions, the amplifier comes with safety mechanisms that cause it to go into protect mode.
How To Find If My Amp Is In Protection Mode
An amp randomly/repeatedly going into such a state is a red flag, meaning there’s definitely a problem cooking up.
This article will deal with different methods you can use for getting out of this mode.
But before this, we’ll discuss why an amp goes into protect mode in the first place and how you can find it.
You will need to look at your amp’s power LED for this purpose.
In normal circumstances, this LED will have a green color. If it’s orange or red instead, it probably means the amp is in protect mode. Some amps have a separate ‘protect’ LED that turns red when/if it goes into such mode.
- How To Change Emoji Color On Android? [Ultimate Guide]
- Snapchat: How To Edit Photos & Videos from Your Camera Roll
- How To Change Your Name On Google Meet And Here's The Step By Step Guide
- How to Transfer Songs from iPhone to iPhone Using AirDrop
- How to Charge GoPro Battery & Camera: 4 Ways (All Models) 7 Charging Tips
Some other models don’t offer either of the above and just turn the power LED off. So, it’s better to check the manual or search online to see which indicator your amp comes with.
Why Is My Amp In Protection Mode
Most of the times, the amp goes into this mode often because of loose wires and improper installation, but there can be other reasons as well.
Load mismatch happens when you plug an amp into the subwoofer with a lower impedance than the minimum threshold for that amp. For example, pairing a 2-ohm sub with a 4-ohm amp will put an extra load on that amp, causing it to go into this mode.
If you notice the amp to go in this mode whenever you hit bass at full volume, then it’s surely due to load mismatch.
The amp is usually placed in cramped areas of a car, such as underneath the seats.
This prevents any airflow and causes the amp to overheat. To prevent its internal parts from melting due to this excessive heat, the amp goes into protect mode.
The amp can also shut down if some other component of your car stereo system is having a problem, such as your head unit or speaker.
Finally, an amp can also shut down if there’s some fault within its internal parts such as output transistors, rectifiers, transformer winding, etc.
How to get your amp out of protection mode
1. Check All The Cables
Before anything else, ensure that none of the power cable, grounding cable, and patch cables is loose (happens when you drive on bumpy roads) or damaged.
If there’s any accumulated dust or rust, you should clean it with a dry cloth.
Lastly, make sure that the amp is not in contact with any metal of the car.
2. Check Amp Temperature
You should touch the amp with your bare skin. If it’s too hot to touch, it’s overheated due to the lack of airflow.
- My TV doesn’t output sound through the DIGITAL AUDIO OUT (OPTICAL) port
- Prime Video Not Working on Roku: How to Fix in Seconds
- How to Trim a Video on Snapchat? [The Ultimate Guide]
- How to Block Ads on Words With Friends [2022 Update]
- How to Tell If a Security Camera Is On: Top 6 Ways
Consider relocating the amp to a well-aired location with good ventilation. If the overheating persists, you’ll need a fan to cool down the amp.
The temperature can also increase if you have a blown speaker, bad grounding, and too low impedance load. So make sure to check for these issues as well.
3. Disconnect The speaker
Here we’ll try to figure out if the problem is with the amp itself or in the speaker attached. Disconnect the speaker wiring and RCA cables, leaving only power, ground, and remote leads connected, and then turn on the amp.
If the ‘protect’ LED has turned off, it means the problem is with the speaker. Most probably, it has blown.
4. Disconnect The head unit
The same goes for the head unit. Disconnect all the cables from the amp to the CD player, MP3 player and radio before turning the amp. If it gets out of protection mode, it means there’s an issue with the head unit or the wiring.
5. Check You Ground Connection
If the ground connection is poor or loose, the amp will not turn on or at least won’t function properly. Most people don’t realize it, but your ground wire must have a good connection for the amp to work without any issue.
There shouldn’t be any paint on the surface you’re making a grounding, and the wire shouldn’t be able to move at all.
Check the above video for more info.
6. Set Your Amp’s Gain
The amplifier gain is the measurement of its ability to amplify an audio signal.
The car amplifiers come with a gain knob. The purpose of this knob is to match the amp’s input to the head unit’s voltage level.
While proper adjustment of the gain will reduce the background noise and sound distortion, not doing so will result in signal clipping, overheating etc. These issues, in turn, may result in the amplifier going into protection mode.